Chimney Repointing and Rebuilds in Kent
Repairs, restoration and full rebuilds on modern and period properties.
Your chimney stack is the most exposed part of your home. It takes the worst of the wind, rain and frost, and when it starts to fail the problems rarely stay at roof level. Prestige Brickwork is a Canterbury-based, family-run brickwork company offering chimney repointing in Kent, as well as repairs, restoration and full rebuilds on modern and period properties
Chimney Repointing in Kent


Mortar joints weather over time. Once they crumble, rainwater gets into the stack, and frost then breaks the brickwork apart. Repointing at the right time is far cheaper than a rebuild.
The type of mortar matters as much as the workmanship. If your property is older, a hard cement mortar can trap moisture inside the masonry, leading to spalling bricks, cracking and damp. We remove the failed mortar carefully, clean the joints thoroughly, and repoint with a breathable lime mortar suited to the age of your building. For modern chimneys, we use cement-based repointing where that is the right material
70Our lime mortars use high-quality natural hydraulic and slaked limes, and we can colour match the existing mortar. At the start of every job we put in multiple pointing samples, so you can choose the colour and finish before we continue. 70a simple way to make sure your chimney repointing in Kent looks right as well as lasting.
A chimney’s longevity depends on checking every part for potential water ingress. Repointing repairs open mortar joints, while replacing spalled bricks restores damaged masonry. The chimney’s mortar cap, known as flaunching, should be sound and sloped to shed rainwater. Pots must be secure, with suitable cowls to help keep rain out while allowing proper ventilation. Where the chimney meets the roof, correctly fitted lead flashings and soakers are essential to prevent leaks. Addressing all these details helps protect the chimney, roof and property for years to come.


Example of chimney flashing repair. The existing tile fillet, which had cracked and begun to fail, was carefully removed to expose the joint between the chimney stack and the roof slope. Fillets like this are prone to cracking and letting water in. In its place, we installed new lead soakers and step flashing. The lead is dressed tightly against the brickwork, with each stepped section tucked into the mortar joints and sealed. This provides a durable, flexible, watertight barrier that moves with the building and stands up to weather for many years.
Lead is used instead of a cement fillet because it stays flexible. A chimney and the roof around it expand, contract and settle at different rates, so rigid cement soon cracks and lets water in behind it. Lead moves with the building without splitting. It is also set into the mortar joints and lapped over the soakers, so rainwater is carried safely onto the tiles below. Properly fitted, lead flashing can last for several decades, making it a far better long-term repair for chimneys across Kent.

The cap (flaunching) that holds the pots in place and allows water to run off is an essential part of a chimney. It is a sloped layer of mortar around the base of the pots, and if it cracks or crumbles, rainwater can get into the stack and cause damp inside the house. Pots in good condition and suitable cowls also play their part. Here you have a metal multi-fuel cowl, suitable for a log burner, which keeps rain and birds out while letting smoke escape freely. Beside it is a clay vented cowl, which allows airflow through a disused flue to prevent damp and condensation. The freshly repointed brickwork below completes the repair.


Chimneys don’t necessarily have to be rebuilt. The vast majority just need a little TLC. This chimney had weathered mortar joints and an exposed top with no proper cap, leaving the brickwork open to rain and frost. Rather than rebuilding, we repointed it in the correct lime mortar, which is breathable and suited to older brickwork, allowing moisture to escape instead of trapping it in the bricks. We then added a new angled cap, rendered on top so rainwater runs away from the flues, and fitted pots and cowls. The result is completely weather tight and good for the foreseeable future, at a fraction of the cost of a rebuild.
Chimney rebuilds
Sometimes repair isn’t enough. A stack that is leaning, badly cracked or crumbling needs to come down and be rebuilt before it becomes a danger to your roof and anyone below. We rebuild chimneys to match the original in style and proportions, using traditional lime mortar on period properties and the right brick for the job, so the finished stack looks as though it has always been there.
Period and listed properties
If your home is listed or in a conservation area, we can guide you through the listed building consent process. We provide clear method statements, detailed material specifications and practical advice based on experience, so your repairs meet conservation requirements.
Why Choose Us for Chimney Repointing in Kent?
- Family-run and honest: Much of our work comes from repeat customers and recommendations.
- The right materials for your building: Lime for period properties, cement where appropriate.
- Rated 4.9 out of 5 from dozens of genuine Google reviews. Customers regularly mention our punctuality, clear communication and tidy sites.
- A stress-free service: We keep you informed from survey and quote through to completion.
Why choose us for chimney repointing in Kent?
Family-run and honest
Much of our work comes from repeat customers and recommendations.
The right materials
Lime for period properties, cement where appropriate.
A stress-free service
We keep you informed from survey and quote through to completion.
Rated 4.9 out of 5 from dozens of genuine Google reviews. Customers regularly mention our punctuality, clear communication and tidy sites.
Areas we cover
We provide chimney repointing in Kent and the surrounding area, including Canterbury, Whitstable, Herne Bay, Faversham, Margate, Ramsgate, Broadstairs, Deal, Dover, Folkestone, Ashford, Maidstone, Chatham, Rochester, Gillingham, Sittingbourne, Sevenoaks, Tonbridge and Tunbridge Wells.
Frequently asked questions
How do I know if my chimney needs work? Warning signs include crumbling or missing mortar, loose or flaking bricks, visible cracks, a leaning stack, and damp patches on the chimney breast or ceilings nearby. If in doubt, we’ll survey it and tell you honestly what it needs.
Lime or cement mortar for my chimney? Lime is usually right for older buildings, because it lets moisture escape and moves gently with the structure. Cement is generally suitable for modern properties. We’ll recommend the right one after seeing your chimney.
Will you need scaffolding? Chimney work normally requires it. We can arrange this for you.
Can you work on listed buildings? Yes. We help with listed building consent, including method statements and material specifications.
Get a Quote for Chimney Repointing in Kent
To discuss your chimney or arrange a site visit, call or WhatsApp 07954 409840, or fill in our contact form. You can also see recent projects and customer feedback on our Facebook page.
